Make sure the correct length bolts are in their proper locations and torque all bolts to 11 ft. Heating Element Before Testing any electrical component, inspect the wiring and connectors for damage. Remove or disconnect the following: Engine right side mount-to-engine bolts Left mount through bolt Fig. Also, since this is more of a direct actuation of the valves, there is less flex due to push rods and a more accurate valve actuation occurs. Print Back to Top Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004 Valve Lash Clearance Adjustment All engines are equipped with hydraulic lash adjusters. Run the engine and check for proper operation.
Since coolant can contaminate the engine oil when a cylinder head is removed, an oil and filter change is recommended. Adapter tools 6912 and 8444 mounted on the block-3. Start the engine and bring it to normal operating temperature, then run the engine above 1200 rpm for two minutes. Make sure the pulley bottoms out on the crankshaft seal diameter. Loosen the timing belt tensioner bolt and remove the timing belt.
The tests on the next page can be used to help find the cause of an intermittent fault. On automatic transaxle vehicles, the torque converter actually forms part of the flywheel. Adjust to specification by tightening the adjusting screw. Remove or disconnect the following: Negative battery cable Fuel System Back to Top 4. Position tool 6848 for use with adapters 8444 and 6912-3. The routing diagram can be found in the engine compartment Fig. In effect, the problem was present at least once, but is not present at this time.
Exploded view of the right side hydro-type engine mounting-3. Tighten the bolts to 105 inch lbs. Rotate the adjuster screw , on top of the alternator, to decrease the belt tension. Refill the engine with new, clean engine oil to the proper level. Valve timing is very important and engine damage will result if the work is incorrect. Place the valve cover into position on top of the cylinder head. This means that you can do more fine-tuning of the engine because you have more control over how much and when air enters and exits the engine.
Any unauthorized commercial use, resale or mailing list database development, utilization or application is also prohibited. Verify that all timing marks on the crankshaft and camshaft sprockets are properly aligned before removing the timing belt and starting camshaft service. When a notch aligns with the sensor, voltage goes high 5. Start the engine, check for leaks and repair if necessary. I'm sure there are other reasons. Page 75 Back to Top 6.
Torque the bolt to 40 ft. Spray engine with Spray Nine, let it sit for 5 to 10 minutes then rinse with cold or hot water. Rotate the front radiator side camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover. Negative battery cable Drive belts Crankshaft damper Timing belt. Disconnect the negative battery cable. Before removing the timing belt, always align the timing marks.
Install the oil pan drain plug and gasket. Remove the alternator and power steering pump from the brackets and move them aside. Remove the crankshaft damper center bolt and washer To install: 1. This repair guide outlines procedures for servicing and repairing vehicles using safe, effective methods. The engine coolant temperature sensor is also utilized for control of the cooling fan. Reinstall the gear cover and retaining stud fastener.
Torque the bolts to 105 inch lbs. Install the drive chain tensioner, but keep it loose at this point. Observe all applicable safety precautions when working around fuel. Connect the negative battery cable. Install the closed ventilation system and the evaporation control system.
Would you like to answer one of these instead? The relief valve spring has a free length of approximately 49. Remove the timing belt cover. Use tool C-4992 or equivalent seal driver, to install the new crankshaft oil seal. Exploded view of the right engine mounting-3. Connect the negative battery cable. This will counterbalance certain reciprocating masses of the engine.
Some procedures require the use of tools specially designed for a specific purpose. Start the engine and check for leaks. Yet, thanks to its compact 6. Pressure type sending units convert liquid pressure into an electrical signal which is sent to the gauge. The flexplate also serves as the ring gear with which the starter pinion engages in engine cranking. Release tension by rotating the tensioner clockwise. Especially these terms, which, like so many others, since they can often refer to the same kind of system using slightly different nomenclature.