Push the lock pin with a screwdriver to release the blade and pull the wiper blade down toward the windshield to remove it from the wiper arm. Repair of damage caused by using a fuel that your vehicle was not designed for may not be covered by your warranty. Use only extensions manufactured by the same supplier as the safety belt. The front wheels are prevented from locking even when the brakes are firmly applied. If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for.
Indicates that vehicle information related to recycling and other environmental concerns will follow. Make sure the headlamps and vehicle accessories are off. Cleaning plastic exterior parts Use a vinyl cleaner for routine cleaning of plastic. Use the black plastic clip located just above the buckle to stow the loose seat belt up at the top, near of the shoulder belt take off point. The readiness light will not illuminate immediately after ignition is turned on. We offer manuals that are comb bound, the pages are printed on both sides, and card stock protects the front and back of the manual that you as a product owner will receive.
Push up on the seat to verify that it is latched into the floor. . Speed sensitive steering The steering in your vehicle is speed sensitive. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners to clean the lamps. Engine coolant temperature Illuminates briefly when the ignition key is turned to On. Carefully insert the headlamp assembly into the vehicle making sure the alignment pins are inserted into the proper holes and into the guide ribs. Transmission operates in first and second gears.
Preparing to start the vehicle Engine starting is controlled by the spark ignition system. Remove the jumper cables in reverse order. Transmission operates in gears one through four. Por favor, respeten el editor y el autor de sus creaciones si sus libros con derechos de autor. Remove the jack and fully tighten the lug nuts to the proper torque specifications in the order shown. If you spill any fuel on the body of your vehicle, clean it off immediately.
Thread the lug nuts on the wheel studs with the beveled face toward the wheel. Use the tip of the lug wrench to remove any wheel trim. Far right for airflow to the rear floor vent. Allow the safety belt to retract to remove any slack in the belt. Auxiliary power point This 12V power point is an additional power source for electrical accessories.
Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 80,000 km 50,000 miles. Refer to Control trac system in the Driving chapter for more information. This action could damage the power steering pump. If fuel is splashed on the skin, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Determine which time zone you are in by referring to the zone map. If your vehicle requires professional service, your dealership can provide necessary parts and service. Safety belt maintenance Check the safety belt systems periodically to make sure that they work properly and are not damaged.
Grasp the shoulder belt portion and pull downward until the entire belt is extracted. Distance to empty display may be inaccurate if the vehicle is started while parked on an incline. At normal operating temperature, the needle remains within the normal zone. To open the liftgate, turn the liftgate handle to the left. Is User Manual Archive a manufacture? To reset, depress the control. Push the lever back up to lock the steering wheel into position. Make sure the parking brake is set.
Slide out the empty tissue box by pulling it up and out. Install the child safety seat in a seating position which is capable of providing a tether anchorage. Slide headlamp assembly forward and off of guide ribs to expose the back of the bulb and wiring connector. Department of Transportation-Tire quality grades: The U. Do not plug optional electrical accessories into the cigarette lighter. To make reaching the wiper blades easier, simply: 1. Buckle the combination lap and shoulder belt.
If this condition persists, damage to the transmission could occur. Hooking floor mat Installing the floor mats 1. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Refer to the Engine data chart for spark plug gap specifications. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength. After at least three to five fuel tank fill-ups, fill the fuel tank and record the current mileage reading.