Cylinder Block 15 Remove the bolts which secure oil pump to cyl- inder block. A vacuum draining device could leave carbon deposits at the bottom of the oil pan and potentially contaminate the new oil. Apply liquid gasket to the oil temperature sensor threads. Spark plug: Do not pull the cord itself. Information subject to change, correction, updating. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Is the canister damaged or is Repair or replace Go to step 9. Be careful Remove the screw which secures oil pump cover not to damage the front oil seal during installation. Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident. Check and adjust the front side belt tension. Be sure to position the claws at the end of the support between the stoppers on the rubber as shown. Then release the accelerator pedal. If the vehicle requires frequent refilling, there may be an oil leak.
An electronic tone will sound. These are normal characteristics of Vehicle Dynamics Control operation and are no cause for alarm. Sedan models Lock Unlock Release button Insert the key into the key cylinder on the seatback, unlock the seatback by turning the key counterclockwise, and then fold the seatback down while pushing the release button. Probe — 8 Start the engine and let it idle. Using poor-quality oil or oil not designed for turbo engines may cause damage to the turbocharger and other engine components.
Check and Confirm all details with your local dealer-mechanic. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. The recall began December 2016. Type A audio set if equipped. Locking and unlocking from the inside. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper. In this mode, the radio scans through the radio band until a station is found.
It is especially recommended on The maintenance schedule is the same regardless of oil used. Replace the valve spring if it is not part. Customer Dealer Services Department P. Vehicle load limit — how to determine. Remove the wiper blade assembly by opening the cover and pulling it down in the direction shown in the illustration. To install the bulb to the headlight assembly, turn it clockwise until it clicks. Release the secondary hood release by moving the lever between the front grille and the hood toward the left.
Always contact your local with any questions and iInspect any vehicle prior to purchasing. Oil Changes Carbon deposits produced by a turbocharged engine can accumulate at the bottom of the oil pan. Make sure to check other engine fluid levels as well. The 92 Legacy with a shift stick and bigger engine still does a tear and outperforms the 2000 and the 2004. Why would you get rid of a Subaru in another 100k? Power steering The power steering system operates only when the engine is running. After highway driving or high-load driving, Subaru recommends allowing the engine to cool by idling for at least 30 seconds before shutting off. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator.
Judgement Value Malfunction Criteria Threshold Value Battery voltage 10. Any driving where the engine speed is kept high — either by using lower gears at higher speeds or using engine braking — is considered racing-type driving. Tightening torque: 8 N·m 0. Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury. To use as full-automatic climate control system. Owners may contact Subaru customer service at 1-800-782-2783.
If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or. Rotating the tires involves switch- ing the front and rear tires on the right-hand side of the vehicle and similarly switching the front and rear tires on the left-hand side of the vehicle. Remove the screwdriver from the hole. If you are handy with tools and procedures, you can save a ton of money if you change the belt yourself. Pull the hood release knob under the instrument panel. Insert the hitch pin into the hole on the hitch receiver tube so that the pin passes through the ball mount. Avoid placing the head restraint in the passenger compartment to prevent it from being thrown around in the passenger.