If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. If the vehicle fails to start after the additional attempts, the remote engine start system will abort and return to a non activated state. When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Even with the security turned off, lock or unlock the doors by depressing the transmitter. After programming the second key, cycle the iginition switch on and off to exit the programming mode this may have to be done twice to effectively exit. To turn the chirp off or back on, unlock all the doors with the unlock button on the remote, then press both the lock and the unlock buttons on the remote for 2 seconds. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.
Private message Comment the review as Subaru Of America verified representative. The horn will honk and the parking lights will flash three times to indicate that the system has entered programming mode. There is no longer an audible honk feature. Hold unlock to open remaining doors. Repeating the procedure will re-enable the keyless entry chirp.
It does not operate when the key is inserted into the ignition switch. Open and close driver's door again. The horn will always honk 3 times if a door is not fully closed when you lock it. At this point you can perform either action Step 5 or Step 6. This unit has a permanent memory, and only requires programming for new remotes. Sorry but I have had a bunch of remote starters and none of them ever shut off when you open the door.
Lock the doors using the power lock switch with the door open. It is much easier to contact your local dealer who can program them for you using a special computer. Subaru Keyless Entry, Security Alarm, Immobilizer Key, Remote Start Systems. I plan to take it to the dealer to get another key, but is there any way to tell if it has remote start otherwise? In this event, perform the procedure again beginning with part 4. This means if you are using 1 remote, push it slowly 5x, if you are using 2 remotes push 1 3x and the other 2x, again a total of 5 times. How it looks: Feb 2006. Horn will sound 2 times to indicate that the remote has been programed.
Alarm Security System: optional on all models. The Modified Life staff has taken every 2008 Subaru Legacy remote start wiring diagram, 2008 Subaru Legacy remote start wireing diagram, 2008 Subaru Legacy remote starter wiring diagram, 2008 Subaru Legacy remote starter diagram, 2008 Subaru Legacy wiring for remote start, 2008 Subaru Legacy remote start wire diagram, 2008 Subaru Legacy remote starter wiring diagram, 2008 Subaru Legacy remote start install diagram and cataloged them online for use by our visitors for free. The red 'security' light will then flash 2 times a second until the car is turned on. Push the small button a second time to unlock all the doors. Test to make sure it's right Deleting old transmitter codes The control unit of the keyless entry system can store 4 transmitter codes. SoA Programming the remote transmitter code from the owners manual read through this first since eveything needs to be done in a quick sequence 1.
I tell everyone it is the worst feature of the car. Chrysler has remote start systems that work just fine allowing you to start, open doors and get in with engine running. Just drop by your nearest dealer. If you still have this, be sure to leave it in the 'on' position, and Subaru recommended turning it on-off every week or so with the car parked and the engine running just to keep the connection clean. Registration is carried out by an authorized dealer using a select monitor and a special program.
The number of flashes indicates the location of unauthorized intrusion or severity of impact. Its basically just a second remote you have to have dangling from your keys, that only has one button on it. Unlock: Right button will unlock driver's door only. The driver's door must be opened and closed between each remote you want to program. Press and hold the black programming button for 10-15 seconds. Horn will sound 3 times to indicate the completion of the procedure.
If you want your response to count towards your company rating, you can also leave a comment for this review. Unauthorized reproduction, copying or use prohibited information is always subject to change and correction. Heres a link to a page that might be helpful to you: 10:30am on Apr 27, 2010. Do not turn the key far enough to start the car, just to the 'on' position so the dashboard lights up. How to find: Call up your local wreckers until you find one. Due to its comfortable interior, superior function in challenging conditions, excellent outward visibility and overall drive quality, your Subaru Legacy has been a standout among competitors in the mid-size sedan market. Use of the keyless transmitter with still lock and unlock the vehicle and arm the alarm , but without the annoying chirping.