The other thing you need to check is, the sensor is magnetic and can catch alot of debris, like metal shavings from a freshly turned rotor or other metal particles. Heated seats if equipped To operate the heated seats: Push the control located on the seat to activate. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized Mazda dealership. Ask the front seat occupant to sit in a rear seat until the air bag system if checked by the authorized Mazda Dealer. Resting your foot on the brake pedal while driving may reduce fuel economy. Pull up the head restraint until it reaches the highest adjustment position. Move the front of the control up or down to raise or lower the front portion of the seat cushion.
Inspect the safety belts to make sure there are no nicks, tears or cuts, replacing if necessary. This would seem to be a safety recall which mazda does not want to own up to. Steps for determining the correct load limit: 1. Wait until the weather clears before trying to drive with the wipers inoperative. Dry the area with a soft cloth. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. Unless all safety procedures are followed, injury can result.
Turn the blade at an angle from the wiper arm. This has only been happening for the last two days. The manufacturer was not notified. The vehicle was not repaired. Dealer diagnosis was that code and need 2 harnesses for side air bags and 2 harnesses for pretensioner. I barely bumped the car in front of me at probably less than 5 miles per hour but my air bags went off.
The independent mechanic was unable to determine the failure. Always dispose of used automotive fluids in a responsible manner. Department of Transportation-Tire quality grades: The U. Sudden braking or a collision could cause serious injury. If there is difficulty in turning the key, rotate the steering wheel until the key turns freely. Turn the ignition to the off position. I have seen many, many complaints about this important vehicle safety system failure online.
When changing the air filter element, only use a genuine Mazda air filter element. Complaint Number: 10218937 Incident Date: February 18, 2008 Date Added to File: February 23, 2008 Description of the Complaint: Air bag warning light. This will ensure that your displays are visible under all lighting conditions. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir an opaque plastic bottle. Remove the jumper cable from the ground metal surface. Dealer diagnosis was that code B1877 and B1994 need 2 harnesses for side air bags and 2 harnesses for pretensioner. Position the jack directly below the protruding bolt.
All seat belts in the vehicle are combination lap and shoulder belts. Tether straps are available as an accessory for many older safety seats. Mazda does not recommend disabling this feature except in situations where speed reduction may be detrimental e. Lift the yellow tab to release the hinges. It could be a bad tire or a broken belt on a tire.
Set the parking brake, press and hold the clutch pedal, place the gearshift in N Neutral , and release the clutch pedal. If you must use a forward-facing child seat in the front seat, move the seat all the way back. The vehicle was not repaired. The fluid should be in the operating range for normal operating temperature. If you press another control within those five seconds, the search will not initiate;. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition is turned back on. This indicates the seat belt is now in the automatic locking mode.
The whole process normally takes 40 days or less. The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. Remove the two screws from the lamp assembly. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar. Refer to Rear window defroster later in this chapter for more information. Make sure the fog lamp switch is in the off position.
Insert the glass end of the new bulb into the headlamp assembly. Insert the lug wrench through the access hole in the rear bumper. Your vehicle is equipped with one of the following dipsticks. See your authorized Mazda dealership. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.